NEWS: Eachine Minicube F4 tower

[Drone News]

As you may already now, the Eachine Minicube is populated most of the last [80-110mm] machines. The minicube is a 3 layers electronic tower where the lower is the 4-in-1 10A ESC BLheli_S+PDB board, the middle one the F3 Omnibus with a builtin OSD and the upper one is the receiver.
Three choice are proposed: FlySky AFHDS-2A, FrSky D8+RSSI and Spektrum DSM2/DSMX. Eachine just released the F4 version: https://www.banggood.com/Eachine-Minicube-20x20mm-F4-OSD-Compatible-Frsky-Flysky-DSM-RX-Blheli_S-10A-For-Aurora-68-90-100-p-1165366.html

Now the main FC welcomes a F4 processor doubling the CPU/FPU capacity and increasing also the number of UART ports. Now no problem to run everything at least at 8Khz. More this the 6-axis stabilization chip is connected via SPI interface, you can run even at 16Khz !!!!
The weight remains the same. Be sure we will see relativement soon new BNF racers with this new minucube revision.

Description:
Brand name: Eachine
Mount hole: 20mm*20mm
Size: 27mm*27mm*20mm
Weight: 9.4g

1. Eachine Minicube Receiver

1). Eachine Minicube DSM2/ DSMX satellite Receiver
Frequency range: 2.403-2.479Ghz
Input power: 5V
Response time: 22ms / 11MS
Resolution: 2048
Display method: LED
Operating voltage: 3.3V
Working current: 60MA
Size: 27mm*27mm*7mm
Mount hole:20mm*20mm
Weight: 3.1 g
Antenna length: 100mm
Data format: Serial port
Protoco: DSM2/DSMX
Distance: no ground interference (1 m from the ground ) > 300m
Uses: indoor small aircraft.
Compatible Transmitters: DSM2 / DSMX series of remote control
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator

2). Eachine Minicube Flysky 8CH AFHDS2A receiver
Channels: PPM 8CH
Model type: Multi-rotor
Frequency range: 2.408-2.475GHz
2.4GHz system: AFHDS 2A
Work Mode: PPM
Transfer method: FHSS
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >300m
Working current: 40mA
Size: 27*27*7mm
Mount hole:20mm*20mm
Weight: 3.1g
Ibus output with failsafe
Compatible Transmitter: Compatible with FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F

3). Eachine Minicube Frsky Compatible 2.4G 8CH Receiver:

Frequency range: 2.403-2.479Ghz
Channels: 8CH
Work mode :D8 Mode
Output: SBUS
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >500m
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Working current: 80mA
Dimensions: 27*27*7mm
Weight: 3.5g
Compatible with FRSKY ACCST
Compatible with X9D(Plus)DJT/DFT/DHT
Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2)

2. Minicube F4 integrated Betaflight OSD
Size: 27*27mm
Mounting hole: 20*20mm
Weight: 3.3g
Processor: STM32F405RGT6
Sensor: MPU-6000 (connected by SPI)
Firmware version: betaflight_3.1.7 OmnibusF4SD
Built-in BEC: 5V/1A
Power supply: 2-4S lipo battery
PPM/SBUS/DSM2/DSMX input
LED_STRIP solder pin
Buzzer solder pin
With LC filter
Built-in OSD (Using F4 MCU controls OSD over SPI bus in DMS mode)
Built-in voltage detection, alarm
Support the newest DSHOT ESC
Support programmable LED_strip (turn off transponder before using)
Support BLheli suite, Blheli_s pass-through ready

3. Eachine Minicube 10A BLHeli_S 4 In 1 ESC:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Firmware version: BLHELI_S 16.5
BB2, 48MHZ Chip
Lipo Battery: 2-3S
Con. Current: 10A
Peak Current: 15A (10S)
BEC: 5V @0.1A
Programming: YES
Betaflight passtrough ready
Dshot600 ready(Default)
Support oneshot42 oneshot125 Multishot Dshot
Damped light on

Package included:
1 x Minicube Receiver
1 x Minicube F4 Flight Controller
1 x Minicube 10A BLHeli_S 4 In 1 ESC

Cet article NEWS: Eachine Minicube F4 tower est apparu en premier sur Drone-Maniac !!!!!!!.

View the full article