NEWS: Happymodel Mobula7, a 75mm 2S Tinywhoop FPV racer

[Drone News]

Here is a direct competitor of the BetaFPV Beta65X, in fact more in 75mm format. It’s a brushless 2S 75mm tinywhoop machine with new 0802 16000Kv: https://www.banggood.com/Happymodel-Mobula7-75mm-Crazybee-F3-Pro-OSD-2S-Whoop-FPV-Racing-Drone-w-700TVL-Camera-BNF-p-1357971.html

We have a F3 flight contoller with a builtin OSD. For the ESC, a builtin 4-in-1 5A (peak @6A) flashed with the last 16.7 BLheli_S firmware compatible with ESC buzzing. Four choices of receiver are proposed: 2 are directly integrated via SPI connexion (FlySky AFHDS-2A & FrSky D8/D16 non-EU) and two with an external receiver (FrSky D16 EU & DSMX/DSM2). For the AIO FPV, a basic 700TVL NTSC CMOS camera coupled with a 25mW/40CH 5.8G VTX. I regret the absence of a 100mW mode and the absence of smart-audio OSD controls. In term of weight, the machine should reach 39g with the batteries installed. So clearly still compatible with indoors applications while having the 2S power for fast outdoors runs. I hope there will be a 65mm version as well…. probably even more lighter.

Specification:
Brand Name: Happymodel
Model: Mobula7
Item Name: 75mm Wheelbase 2S Brushless Whoop FPV Racing Drone
Wheelbase: 75mm
Version: Basic Version / Standard Version ( Optional)
– The diffirence of them are the package charger.
Basic Version: USB Charger
Standard Version: 6-way Charger
Receiver ( Optional): Compatible Frsky NON-EU Receiver
Compatible Frsky EU-LBT Receiver ( XM+ Receiver)
Compatible Flysky AFHDS/ AFHDS-2A Receiver
Compatible DSM2/DSMX Receiver
Size: 98mm*98mm*36mm
Weight: 25.9g (without battery)

Crazybee F3 Pro Flight Controller
Item Name: Crazybee F3 Pro FC
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-2S battery input (DC 3.5-8.7V)

Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Receiver ( Diffirent version having diffirent receiver)
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 14A
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready

Firmware
(Frsky version) CRAZYBEEF3 PRO FR Firmware target: CrazybeeF3FR
(Flysky version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
(DSM2/DSMX version) CRAZYBEEF3 PRO Firmware target: CrazybeeF3DX
(Frsky EU-LBT version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS

Onboard 5A 4 In 1 ESC
Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v)
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_7.HEX
Default protocol: DSHOT600

Onboard Frsky NON-EU receiver Version
SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m

Onboard Frsky EU-LBT Version
(XM+ receiver)
Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware Upgradeable, Default firmware EU-LBT with RSSI

Onboard Flysky receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m

Onboard DSM2 / DSMX receiver version
Serial bus receiver
Protocol: DSM2/DSMX compatible
Channels:6-9 (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m

SE0802 16000KV Motor
Model: SE0802
KV: 16000KV
Configu-ration: 9N12P
Stator Diamter: 8mm
Stator Length: 2mm
Shaft Diameter: Φ1.0
Motor Dimension (Dia.*Len) : Φ10.5*14.5mm
Weight: 1.8g
Support 1-2S Lipo

No.of Cells: 1S Lipo
Propeller
40mm 3-blade Propeller ( 4 CW + 4 CCW)

5.8G VTX AIO Camera

5.8G 40CH 25mW VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
700TVL FOV120 Camera
Camera resolution: 700TVL
Field of view: 120°
Video Format: NTSC
Antenna: RG178 antenna
Frequency: 5.8GHz 5bands 40 channels
With Raceband
Smartaudio ready(Frsky EU-LBT and DSMX version not compatible)
Size: 13.9″12.0mm ( L*W )
Weight: 3g

Lipo Battery
Capacity:250mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 55mmx12mmx7mm
Weight: 6.5g
Connector: PH2.0
Notes: Need 2pcs batteries for Series circuit

Features:
– New Crazybee F3 PRO Flight controller 1-2s Lipo compatible
– 2S whoop more powerful and more flight time
– Betaflight support , multi flight mode: ACRO/AIR/ANGLE
– New 0802 Powerful and High efficiency Brushless motor and Smooth ESC
– Smartaudio ready , change VTX bands, channels via OSD
DSM2/DSMX and Frsky EU-LBT version are Serial-based receiver, so Smartaudio is not compatible.
– Adjust the settings and the PID of the flight controller via OSD
– Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
– Flysky version support both AFHDS and AFHDS-2A protocol transmitter
– DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
– Frsky EU-LBT version support Frsky EU-LBT firmware transmitter
– Full telemetry function ready
– Head lights ready
– Camera angle adjustable
– Real Bind and Fly version
– Buzzer Ready

Package Included:
Basic Version
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x USB Lipo/LIHV Charger
1x Fixing Mount for Lipo Battery
1x Propeller Disassemble Tool
1x Screwdriver

Standard Version
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x 1S06 6 Way Lipo/LIHV charger
1x Propeller Disassemble Tool
1x Fixing Mount for Lipo Battery
1x Screwdriver

View the full article